Seven steps to use a peanut peeler

Peanut peeling machine is the ideal equipment for removing peanuts, almonds and broad bean skin. It can be used in the production of large-scale manufacturers with the fried peanut production line. This machine can also be used to remove the outer skin of almonds and broad beans. Now it has been improved, after replacing some parts, you can take off the outer skin of the almonds. Below we introduce the steps of using the peanut peeling machine:
1. Before using the peanut peeling machine, first check whether the fasteners are tightened, whether the rotating part is flexible, whether there is lubricating oil in each bearing, and whether the peeling machine is placed stably. In order to ensure the safety of the operator, the outer casing of the motor must be grounded (the outer casing of the motor is reliably connected to the grounding body).
Second, before the application of power, the peanut peeling machine will be turned a few times. If there is a crash, the cause should be identified and the power should be re-energized.
Third, the appropriate sieve should be selected according to the size of the peanut kernel.
4. After the power is turned on, try the test first and pay attention to whether the rotor is turning correctly. After the motor is started, the steering of the rotor should be consistent with the direction indicated on the implement. First idling for a few minutes, observe whether there is abnormal noise, and the operation is normal and stable before the peanuts can be quantitatively, uniformly and continuously put into the hopper.

5. There are also requirements for the degree of dryness and humidity of peanuts, that is, peanuts should not be too dry or too wet. Too dry, the peanut break rate is high; too wet, the speed of shelling will be slower. In the winter, the peanuts stored in the rural areas are generally dry. To make them dry and wet, the following methods can be used: evenly spray about 100 kg of peanuts with about 15 kg of warm water, cover with plastic film for about 10 hours, and then dry in the sun. It takes about 1 hour to start shelling. It takes only about 6 hours to cover with plastic film in other seasons, and the rest of the operation is the same.
Sixth, to solve the increase in peanut shells is to move the motor down, in order to tension the fan belt, increase the amount of blowing.
7. When peeling, the peanut fruit should be fed evenly and properly. It is not allowed to mix iron scraps, stones and other debris to prevent the peanuts from breaking or causing mechanical accidents. The outlet switch can only be opened when the peanut kernels are covered with a sieve surface.

Manufacturers of charcoal machines must have a more complete management mechanism

A manufacturer should have a better management mechanism to have a healthier production scale. For a machine charcoal machine that is more popular now, the manufacturer of such a machine should have a more complete management mechanism. Xiaobian I want to discuss a topic with you today, I hope to be helpful to everyone.

First, manufacturers should have better and better management talents. For managers or managers of enterprises, they must have better and more high-end management methods and strategies, so that they can develop appropriate business strategies and business methods for enterprises, and also enable enterprises to have more Good vitality.

For more knowledge, please contact our E-mail：allenshuliyguo@gmail.com

http://www.charcoal-machines.com/

Peanut sheller machine

When the peanut sheller is used normally, the temperature of each component should also be kept in constant attention. Because the temperature of some components is too high, it is often a precursor to component damage.

     The HT series peanut sheller produced by Tongshun Peanut Machinery uses a V-belt drive. After a long period of use, the belt will gradually stretch and relax due to the pulling force. If the temperature of the pulley is increased, it is necessary to check whether the belt is slippery or not, or tighten or replace according to the situation, so as not to cause the peanut peeling machine to rotate too low. The working temperature of the motor should not exceed 60 degrees Celsius. If the motor temperature is too high, it is necessary to stop the circuit immediately to ensure that the voltage reaches or approaches 380v, and the 2-phase motor needs to reach 220v. The temperature of the bearing should not exceed 25 degrees Celsius. If the temperature of the bearing housing is too high, stop the bearing immediately and check if the bearing is damaged to avoid further damage.

     The above description is for reference only, more details can be inquired.

For more knowledge, please contact our E-mail：allenshuliyguo@gmail.com

The urgency of improving the existing peanut picking machine

In view of the common problems of existing peanut pickers, the problems of unstable performance and blockage of peanut pickers will be solved in the future development, and the productivity will be further improved and the loss rate of peanut pickers will be reduced. At the same time, according to the consumption level of farmers in China, the cost control of peanut picker should be within a reasonable range. After China's entry into WTO, we must understand the latest developments of peanut pickers both at home and abroad, grasp the development trend of peanut pickers, with the help of advanced technology and experience at home and abroad, and take the market as the guide, speed up the development of peanut pickers which conform to China's actual situation and have Chinese characteristics. Open the new development of peanut picking machine. At present, the application of semi-feeding harvesting method at home and abroad is not much, mostly used in combined harvesting. Because of the different planting techniques, most areas of our country implement subsection harvesting or combined harvesting.


The research on peanut combine harvester in mainland is relatively late, and the technology needs to be improved. There is no formed peanut combine harvester to meet the production requirements. Because of this relatively high production cost and safety considerations, it has not been applied to fruit picking machines. How to improve the feasibility of applying this method to a separate fruit picking machine needs further study. In structure, the structure of the drum, the selection of the clamping device, the relative position relationship between the drum and the clamping device, and the angle of the conveyor belt need to be further studied in order to obtain a more reasonable structure and reduce the harvest loss. In terms of working parameters, a large number of experiments were carried out on the feeding quantity of peanuts and the speed of picking roller. While the structure is improved, the relevant working parameters are verified, and the related multi-factor tests are carried out to obtain better working parameters. To sum up, the application of half feeding mode is still not perfect. There is still much work to be done in terms of structure and parameter selection. This not only has certain scientific value in academia, but also has great practical significance for production practice.

For more knowledge of charcoal machine, please contact our E-mail：allenshuliyguo@gmail.com

How to make environmental protection charcoal machine in the great environmental protection situation?

As we all know, the general trend of all countries in the world is environmental protection, whether in all industries are required to achieve environmental protection and smoke-free, we put forward the purpose is "not Jinshan Yinshan, as long as green mountains and rivers." In such a big situation, how to make environmental protection charcoal machine is worth considering.

Shuley Machinery is a professional manufacturer of charcoal machines. We have already produced environmental protection charcoal machines in the early years, because we all know that environmental protection must be done. The old charcoal machines were backward in technology, and the appearance and internal design were not very reasonable. So after years of research on Acer Machinery, We have been far ahead in the field of environmentally friendly charcoal machinery. Everyone knows that in the process of production, it will produce the flue gas which pollutes the environment, and it will also produce harmful substances such as wood tar, wood acetic acid and so on. So the new research on the environmental protection charcoal machine of Acer Machinery can not only do smokeless environmental protection, but also reuse these exhaust gases and so on. The composition of environmental protection charcoal machine is composed of Wood crusher, dryer, Sawdust briquette machine, carbonization furnace four equipment, we introduce one by one our new design of these equipment environmental protection principle.

Grinder

If the crusher is to crush the larger raw materials to the size we need, in the process of material particle size is small, so there will be dust or a large number of dust, so workers at work not only may inhale respiratory tract disease, but also will be emitted in the air pollution. According to the customer's reaction, we have a new design of the crusher behind the part of a salon can do a buffer, and the outlet of the salon and the second buffer of the air-blower, and finally through the bag of dust thoroughly disposal of these dust and so on, so in the process of work there will be no previous pollution air. The situation of gas.

For more knowledge of charcoal machine, please contact our E-mail：allenshuliyguo@gmail.com

What is the working principle of the charcoal in the charcoal machine?

The carbonization furnace in the charcoal machine uses a self-produced gas furnace as a heat source, uses methane gas through a cyclone, and distributes air into the burner. The outlet temperature of the burner can reach 800 ° C to 1200 ° C, and the flow rate can reach 3 to 5 meters per second. The high-temperature airflow is heated in the periphery of the combustion chamber. It should be noted that when heating, the furnace temperature is between 100 ° C and 150 ° C, which is a greater value of moisture in the furnace. When the raw material rod is put into the kiln, 4 to 8% of water is brought into the furnace. 1700kg of raw materials can bring more than 100 kilograms of water. These waters are the enemy of carbonization. Because the mechanism carbon rods are very afraid of moisture, the water is pulverized into powder, which seriously affects the quality of carbonization. Therefore, the moisture removal system is essential. The key is that the tidal time is 1 to 1.5 hours. When the temperature in the carbonization chamber rises to 300 °C, a large amount of combustible gas is generated in the furnace. Each kilogram of raw material theoretically produces three cubic methane gas, which can be carbonized. Heating, drying heat source, the temperature of the furnace can be adjusted at will, low temperature carbon is generally above 400 ° C (8 hours can be completed), high temperature carbon is above 600 ° C (10 hours to complete)

Screw oil press features

Disadvantages of traditional oil extraction methods: original workshop, simple equipment, heavy operation, large floor space, high energy consumption, low oil yield and poor sanitary environment.
   The product is fully efficient, energy-saving, advanced in design, beautiful in appearance, reliable in performance, simple in operation and convenient in maintenance.
   The oil yield is high--compared with the old-fashioned equipment, the normal oil yield can be 4-6 percentage points higher, and the average peanut oil per processing can produce 4-6 kg more oil. The annual economic benefits are considerable.
   Energy-saving - the same output reduces electric power by 40%, and saves an average of 6 kWh per hour. The daily production can save 30 yuan in electricity.
   Labor saving - the same output can save 60% of labor, 1 to 2 people can organize production, and save labor costs of about 40 yuan.
   Wide use - multi-purpose machine, can squeeze more than 20 kinds of oil crops such as peanuts, sesame seeds, rapeseed, cottonseed and soybean. Multi-stage pressing, one squeeze at a time.
   Pure oil--vacuum filtration, to ensure the purity of oil, in line with health and quarantine standards.

   The small area - the oil square can only be used 10-20 square meters.

The oil press machine is suitable for rapeseed, peanut kernel, soybean, oil sunflower, rapeseed, flax, tea seed, sesame, olive, walnut, corn germ, rice bran, tea seed, safflower seed, sea buckthorn seed, neem seed, Plant oils such as rubber seeds, pepper seeds, tomato seeds, watermelon seeds, grape seeds, flaxseed, evening primrose, pepper seeds, castor beans, citrus seeds, cocoa beans, coffee beans, perilla, almonds, peach kernels, rose hips, etc. .

Peanut roaster machine operation process

Peanut roaster machine is an important peanut equipment in the processing of peanut food. The use of the peanut is strictly in accordance with the following procedures:

1. Press the main power switch: the user configures the main power switch (power switch), and connects the power cable from the main power switch to the electric oven.

2. Power the oven: After checking the operation of the equipment, press the power switch to supply power to the oven.

3, no-load heating, debugging equipment: press the cage forward rotation switch, let the cage rotate for 3~5 minutes, then press the heating switch to heat the electric heating tube to the cage, then use the screwdriver to adjust the temperature controller The upper temperature control knob adjusts the upper and lower limits of the temperature in the desired oven (the digital display of the temperature controller can be used to know that the temperature difference between the upper and lower limits is generally adjusted to 3 to 5 degrees). When the heating temperature reaches the upper limit, the electric heating tube stops heating, and the temperature begins to decrease slowly. When the temperature drops to the lower limit temperature value, the temperature controller restarts the electric heating tube to heat, so that the material is repeated until the material is baked. Bake until required.

4. Timing alarm debugging: After the 3 steps are adjusted, press the time switch again to adjust the required set time. You can set the time to adjust the time in the control box. 0~99 minutes arbitrary adjustment), after a period of time, the bell sounds alarm, which means that the time required for baking has arrived. The operator then turns off the timer switch, at which point the bell no longer alerts.

5. The material is released from the cage: after the alarm is alarmed, the timer switch is turned off. Open the door panel of the material outlet, let the discharge port open, then press the cage stop button, after 3~5 seconds, then press the cage reverse button, the material will be screwed out of the cage, from the discharge The mouth is drained until the material is emptied. Finally, close the door panel and press the stop button. After 3~5 seconds, press the forward button again, then the cage will start to rotate forward again.

Want to know about our machine, you can send the question to E-mail: allenshuliyguo@gmail.com

Sawdust briquetting machine can not normally discharge the solution

Some customers who have just started to use the sawdust briquetting machine to produce mechanism carbon have encountered the mechanism that the charcoal machine can not be discharged normally. Don't panic at this time. Hongrui Machinery Design Department will introduce the solution in detail for everyone:
First: the diameter of the head screw and the second screw of the sawdust briquetting machine are not well matched, and may be too far forward;
Second: the sawdust briquetting machine is not exhausted;

Third: the forming cylinder is not tightened or loose, and the screw head collapses and wears seriously, which also causes this phenomenon;
Fourth: the production temperature of the sawdust briquetting machine is too low, and the screw head is too large, the extrusion material can not be digested immediately at the forming port, which causes a very large friction force between the raw material and the barrel wall, which makes it difficult for the charcoal machine to be normal. Discharge, and will go backwards.

Want to know about our machine, you can send the question to E-mail: allenshuliyguo@gmail.com

Top ten precautions for using peanut machinery

Peanut machinery is the main product of our company. We always ask ourselves to recommend high-quality, low-priced products to consumers. Here is a brief introduction to the top ten things to use peanut machinery:
    1. First check whether the fasteners are tightened, whether the rotating part is flexible, whether there is grease in each bearing, and whether the shelling machine is placed on a stable ground.
    2. To check the power supply voltage, the switch must be in the off position.
    3. After the motor is started, the steering of the rotor should be consistent with the direction indicated on the machine. First idle for a few minutes, observe whether there is abnormal noise, and confirm that the operation is normal before feeding the peanuts.
    4. When peanuts are fed, they should be even and proper. Do not contain iron filings, stones, etc., so as not to break the peanuts or cause mechanical accidents. When the peanuts cover the sieve surface, the mouth switch can be opened.
    5. When the peanut shells in the peanuts increase, the motor can be moved downward to tighten the fan belt and increase the blowing volume.
    6, when operating, people do not stand on the side of the belt, so as not to hurt people.
    7. When using the machine to be stored, the dust and dirt on the surface and the residual grain and other debris should be eliminated. The machine should be covered and placed in a dry warehouse to avoid sun and rain.
    8. Remove the drive belt and keep it separately.
    9. Clean the bearings with diesel oil, dry and apply grease.
    10. It should keep sufficient lubricating grease in the transmission part and bearing room, and clean and replace it regularly.

Want to know about our machine, you can send the question to E-mail: allenshuliyguo@gmail.com

The importance of auxiliary equipment for charcoal machine equipment

The premise of the mechanism charcoal production is that the particle size of the raw materials and the moisture content of the raw materials must be guaranteed. The raw materials are the basis of the mechanism of charcoal, and also the strong guarantee of the high-quality mechanism of charcoal products. For the general mechanism of charcoal briquette production line online, The requirements for raw materials are relatively strict, and the strict standards are mainly reflected in the humidity of raw materials and the length of raw materials, which determine the quality of finished charcoal. The important mechanism of charcoal machine equipment, the mechanism of charcoal machine is inseparable from the pulverizer equipment and dryer, the main function of the dryer, can dry the charcoal raw materials well, effectively control the size of the humidity, and smash The machine can effectively smash large raw materials and control the particle size of raw materials to meet production standards.

Want to know about our machine, you can send the question to E-mail: allenshuliyguo@gmail.com

Peanut processing machinery to reduce energy consumption

Prior to the absence of peanut processing machinery, peanuts were manually processed by hand, which was time consuming and labor intensive. With the rapid development of agricultural mechanization, since the emergence of new types of machinery, it has been widely used because of its high speed, time and effort, and high work efficiency. So for us, what should peanut processing machinery use to reduce energy consumption?
In order to improve the production efficiency of the machine, the processing quality and the uniform load of the processing drum, the processing claws are arranged on the toothed rod according to the principle of three spiral lines. When the drip roller rotates once, there will be three processing claws at a certain point, that is, the peanut stalk can be struck and pushed three times at a certain point, which not only improves the picking rate, but also improves the production. effectiveness.
In general, in order to make the production simple and easy to install, the toothed rod is made to be six according to the dimension. When installing, every other one, count down once. The machining claws are then fixed to the rack, and the arrangement of the claws on the circumference forms three spirals. If the claws are fixed after installation, be careful to keep the bending direction of the claws the same.
During operation, if you hear an abnormal sound or find a fault, you must stop the inspection, promptly eliminate the fault, prohibit the machine from being sick, and strictly prohibit mechanical overload.
Today, peanut processing machinery is widely used in peanut picking and deep processing. If you can master the method of reducing energy consumption in peanut processing machinery, it can not only improve product efficiency, but also greatly reduce power consumption. The company produces peanut shelling machine, peanut butter making machine, etc.

Want to know about our machine, you can send the question to E-mail: allenshuliyguo@gmail.com

How to choose a good sawdust briquetting machine

The Sawdust briquette machine is the key equipment for the production of mechanism carbon. Its pros and cons directly affect the quality and cost of charcoal. Therefore, it is very important to purchase a high quality bar machine.

We should choose a quality bar machine with the following conditions:

1. The motor must use the national standard product produced by the factory.

Never use a refurbished motor or a non-national standard motor to charge. Because the copper enameled wire diameter of these motors can not meet the rated current requirements of the bar machine. Therefore, the motor is easy to burn or the driving force is insufficient, which affects the life of the bar machine and the quality of the salary bar (semi-finished product), thus affecting the quality of the mechanism carbon.

2. The bearing should be a famous brand product produced by the three major bearing factories in China.

They are ZWZ bearings produced by Wafangdian Bearing Group Co., Ltd.; HRB bearings produced by Harbin Bearing Group; LYC bearings produced by Luoyang Bearing Group Co., Ltd. Bearings produced by other small factories other than the ones should not be used. Because of the advantages and disadvantages of the bearing directly affects the production efficiency of the bar machine and the quality of the salary bar. Users should also be reminded here that the Wafangdian bearing can only be described as a product produced in the Wafangdian area, not necessarily a ZWZ brand-name bearing, and special attention should be paid to counterfeit products.
3, electrical components must use the national standard products produced by the big factory.

There are many domestic manufacturers of contactors, current transformers, ammeters, voltmeters, temperature controllers, buttons and other products, but some manufacturers produce products that do not meet the safety and quality standards required by the state. These products are not bad on the outer surface, but they have a short service life and poor safety performance. 4, the thickness of the steel plate must meet certain requirements: the bar machine panel (steel plate for fixed bearing seat) should be greater than 8 ± 0.2mm, or take reinforcement measures; the steel plate of the fixed motor should be greater than 10 ± 0.2mm, otherwise the steel plate is easy to deform, Affect the quality of the bar machine.
5. The processed parts should meet the following requirements:

1 The flange of the bearing seat and the hopper seat must have sufficient thickness. The drive shaft, bearing hole, forming cylinder, taper sleeve and screw propeller must be processed according to the design requirements. The outer surface of the casting must not have floating sand; the interior cannot have obvious trachoma. And other defects.

2 Both sides of the pulley should be machined, and there must be no uneven objects outside the design.

3 The motor wheel is generally applied in solid form and the sides should be machined flat.

4 The thickness of the electrical operation panel should be ≥ 2mm. The front end of the spiral propulsion rod should be welded with alloy welding rod and sprayed alloy powder, and smoothed as required to make the angle and taper meet the design requirements.

Want to know about our machine, you can send the question to E-mail: allenshuliyguo@gmail.com

New carbonization furnace smoke-free and highly sought after

Earth kiln charcoal is a charcoal fired from a traditional earthen kiln. Because the earth kiln does not have a tar separation device and temperature control, the charcoal that is fired has a phenomenon of pinching and produces a smoke smell when burned. In addition, its burning time is shorter than the mechanism carbon. However, due to the low raw material and production cost of the earthen kiln charcoal, and a certain market, some charcoal fired trees cut down the wood to burn the earthen kiln charcoal regardless of the national three-in-five order. In particular, some charcoals cut down rare broad-leaved eucalyptus trees only for their immediate interests. This not only destroyed forest resources, destroyed ecological balance, but also violated relevant national laws and regulations. The carbonization process of a carbonization furnace can generally be divided into the following three temperature ranges:
First, the drying stage
From the start of ignition to the temperature of the furnace rising to 160 ° C, the moisture contained in the mechanism rod is mainly evaporated by the amount of external heating and the heat generated by the combustion itself. The chemical composition of the mechanism rod has hardly changed.
Second, the initial stage of carbonization
This stage mainly relies on the combustion of the rod itself to generate heat, so that the furnace temperature rises to between 160 and 280 °C. At this time, the wood material undergoes a thermal decomposition reaction, and its composition begins to change. Among them, the unstable composition, such as hemicellulose, decomposes to form CO2, CO and a small amount of acetic acid.
Third, the comprehensive carbonization stage
The temperature at this stage is 300 to 650 °C.
At this stage, the wood material undergoes thermal decomposition abruptly, and a large amount of liquid products such as acetic acid, methanol, and wood tar are produced. In addition, flammable gases such as methane and ethylene are generated, and these flammable gases are burned in the furnace. Thermal decomposition and gas combustion generate a large amount of heat, causing the furnace temperature to rise, and the wood material is dry-distilled to char at high temperatures.

Want to know about our machine, you can send the question to E-mail: allenshuliyguo@gmail.com

Detailed description of the maintenance of the peanut sheller machine

Peanut sheller machine maintenance matters
1. The peanut sheller machine is conveyed by a V-belt. After the new belt is used for a period of time, the tensile force will gradually elongate and appear slack. Therefore, it is necessary to regularly check the tension of each transmission belt and the clearance of each mating part, and adjust it in time.
2, peanut shelling machine during the operation, should always pay attention to the machine's speed, sound, temperature is normal. Every time after removing one type or one day of work, it should be stopped to check whether the bearings are overheated, whether the fastening screws and key pins of various parts are loose. If it is loose, it should be tightened at any time, especially for high-speed parts, such as: Whether the fan blades, especially the lower fan blades, are worn or broken, whether the reinforcing plates for external use of the blades are worn or deformed, and if problems are found, they should be repaired or replaced in time.
3. For the suspension shaft of the sieve body and all the joints of the joints, it is necessary to check in time whether there is any oil shortage and wear. After each operation, the bottom of the sieve machine, that is, the hole in the slats, is regularly cleaned with a wire brush.
4. After the processing season is over, the machine will be inspected once. Check the running and wear of each bearing; check the screen bottom for deformation or cracks; check the wear of the sorting screen. After the inspection, repair the damaged parts to remove dirt and residual peanuts from the machine.
5. After the peanut sheller machine is used, remove the belt and place the machine in a dry warehouse for storage. The removed belt should be hung on an indoor wall that is not exposed to the sun.

Want to know about our machine, you can send the question to E-mail: allenshuliyguo@gmail.com

Introduce the storage precautions of the peanut sheller machine

When using the peanut sheller machine, please follow the steps below to avoid accidental injury. The following are the precautions for the storage of the peanut peeling machine:
  1. Before using the peanut sheller machine, first check whether the fasteners are tightened, whether the rotating part is flexible, whether there is lubricating oil in each bearing, and whether the peeling machine is placed stably. In order to ensure the safety of the operator, the outer casing of the motor must also be grounded (the motor's outer casing is reliably connected to the grounding body by wires).
Second, before the application of power, the peanut peeling machine will be turned a few times. If there is a crash, the cause should be identified and the power should be re-energized.
Third, the appropriate sieve should be selected according to the size of the peanut kernel.
4. After the power is turned on, try the test first and pay attention to whether the rotor is turning correctly. After the motor is started, the steering of the rotor should be consistent with the direction indicated on the implement. First idling for a few minutes, observe whether there is abnormal noise, and the operation is normal and stable before the peanuts can be quantitatively, uniformly and continuously put into the hopper.
5. There are also requirements for the degree of dryness and humidity of peanuts, that is, peanuts should not be too dry or too wet. Too dry, the peanut break rate is high; too wet, the speed of shelling will be slower. In the winter, the peanuts stored in the rural areas are generally dry. To make them dry and wet, the following methods can be used: evenly spray about 100 kg of peanuts with about 15 kg of warm water, cover with plastic film for about 10 hours, and then dry in the sun. It takes about 1 hour to start shelling. It takes only about 6 hours to cover with plastic film in other seasons, and the rest of the operation is the same.
Sixth, to solve the increase in peanut shells is to move the motor down, in order to tension the fan belt, increase the amount of blowing.
7. When peeling, the peanut fruit should be evenly and properly fed. It is absolutely not allowed to mix iron scraps, stones and other debris to prevent the peanuts from breaking or causing mechanical accidents. The outlet switch can only be opened when the peanut kernels are covered with a sieve surface.
8. After using the peanut peeling machine, before storing the machine, the dust, dirt and residual grains and other debris in the machine surface should be cleaned, then the bearings of each part should be cleaned with diesel oil, dried and coated with butter. The parts should be repainted again. After the paint is dried, cover the machine and store it in a dry warehouse. The belt should be removed and hung on an indoor wall that is not exposed to the sun.

Want to know about our machine, you can send the question to E-mail: allenshuliyguo@gmail.com

That kind of raw material is more suitable for charcoal briquette production line equipment production mechanism charcoal

The production mechanism of charcoal is widely used, and the raw materials are more suitable for the production mechanism of  charcoal briquette production line equipment. Charcoal raw materials are: sawdust, rice husk, melon skin, coconut shell, dregs, bamboo, walnut skin, branches, bark, trunk, wine Slag, vinegar residue, furfural residue, peanut shell and all kinds of hard wood, nut shell and so on. These can be used to make charcoal. The main part of the production of charcoal machines is to dispose of garbage and waste. Therefore, it is not said that the wood carbon produced by which raw materials is good and the quality of wood carbon produced by which raw materials is poor.
    Although the effect of wood carbon produced by various raw materials is not bad, but there is still a difference, that is, the technology of carbon, according to our experience, hardwood made from straw husk The quality of carbon is higher. If there is no good carbon-making technology, the difference in calorific value between the two will not be too great. Therefore, good quality charcoal must have good raw materials and good charcoal technology. .

Want to know about our machine, you can send the question to E-mail: allenshuliyguo@gmail.com